Keurig Not Brewing A Full Cup Visio For Mac

I bought the brewing descaling solutions and spent all day AND HALF the night running 2nd rinses through MY Keurig 2.0. OUT of desperation I found this sight and tried the small PAPER CLIP TRICK, AND SHAZAM, I GOT a healthy stream of WATER and YOU should've seen all the coffee grounds that came out,even AFTER I took IT apart and cleaned IT. So happy NOW.because I talked HIM into buying THE Keurig brewer, IF IT wouldn't work I would've NEVER heard the END of IT. THANK YOU,THANK YOU, T. They suggest to use a paper clip to clean the nozzle. DO NOT USE A PAPER CLIP.

1. Keurig Not Brewing A Full Cup Visio For Machine
2. Keurig Not Brewing A Full Cup Visio For Macbook

You will possibly rupture the soft plastic elbow above the spout, and you will get an internal leak. It will temporarily work, but it will eventually destroy your unit with a slow leak dripping internally on the components. Use a blunt plastic toothpick or something similar. The real culprit that stops flow totally is the pressure valve located under the hood of your unit, and if you remove the screws that holds the top on (mine is a k60), that you can see when you open your unit, remove the top, and squeeze this valve, it will start flowing again, and then you can run your vinegar through the unit. I first turned it upside down and shook it a few times- that seemed to make the pump kick into action as it was only making noise and no water. It began to work but weak and produced about 1/4 cup water. It was backed up and I noticed water spitting out the over flow valve (white rubber thing located on the reservoir side of the machine).

Please understand that we will not compromise our standards for quality coffee. For fans of the Keurig, there is hope! Our research on K-cups led to one very disturbing fact..there is not enough coffee in a K-cup to make a decent cup of coffee. Secure Log On Ensuring the security of your personal information online is a top priority for us. We encrypt both your User ID and Password using Secure Sockets Layer (SSL) technology - the highest level of protection available online.

Then used the paper clip on each side of the 'needle' in the head of the machine. It then made a full cup, but slowly. Time to descale- added straight vinegar to the reservoir pumping it through until add water light came on then rinsed reservoir and continued with clean water again until add water light came on. Now the stinker works like new.

Thank you for the paper clip idea- brilliant!! This morning at 4:15 a.m., I am using the paper clip for the third time to get a cup of coffee, and I have had this unit less than a month. Poured a bottle of descaler it in and followed the directions.

Used that orange thing Keurig sent me, and followed the directions. I got a stream for the first time, not spurts and spits. The water was actually steaming. I have even been placing my cup in the microwave to heat it properly. When I get home from dialysis, I hope this machine still produces a stream of hot water. I think I was up to cleanse number ten out of the twelve recommended. This is ridiculous for a new machine, especially the Keurig brand.

FOR THOSE THAT USED THE PAPERCLIP WITH NO RESULTS: Used the paper clip and it didn't work. I placed a straw over the object that punctures a hole in the coffee pod and blew air through the line- this don't work (btw, the water reservoir needs to be detached if you're going to blow water through the line). I then sucked on the straw once for about 5 seconds and extracted a large amount of water in that short time. Coffee maker works now!!!

Water was not running through at all and this fixed the back up in the line. Just as a precaution, the water is extremely hot when you extract it from the machine via a straw you will get a mouthful of near boiling water. I have a similar Keurig. The 'flow' was low.

I started to cleaned it with vinegar but didn't wait the recommended time. It stopped working.

It would hiss but the pump didn't work and it wouldn't draw from the reservoir. If I shook it, it would dribble a little water and shut off. I took it to the garage, removed the reservoir and blew air through the lines. I took it back into the kitchen.

It worked once and then made the 'steam' noise. My son, a generation X'er suggested that I call Keurig so I did. I explained the problem and explained what I did and they decided to send me a new one. I threw the old one out. Later, I explained the problem to my grandson - the 'miracle' gen-millennium.

Intel Core 2 Duo T 2. Using the Memory Advisor or Scanner on Crucial. The touch pad also features wide vertical and horizontal scroll regions along sony vaio vgn-nw270f right and bottom edges, respectively. It sony vaio vgn-nw270f a rough, textured feel to it, which might take some getting used to. SONY VAIO VGN-SZ55GN DRIVER FOR MAC DOWNLOAD - Information about charging USB peripherals using Windows 8. Visit our Community and share your experiences and solutions with other Sony customers. Click to DVD 2. The battery charge has decreased after I resume my computer back from hibernation mode or shutdown. Sony vaio vgn-sz55gn Centres List of Sony offices in Asia Pacific region vaioo provide after-sales sony vaio vgn-sz55gn activities. Your RAM must be compatible with your system — or your system just won’t work. Actual battery life may vary with different operating conditions and settings. Notice to Customers of Sony VAIO Personal Computers Regarding Use of Genuine Sony Rechargeable Battery Packs Windows 10 information - updated on 28th July 2015 End of support notification for products using the Windows Vista operating system. Sony vaio vgn-sz55gn drivers for mac.

I retrieved it from the trash He tried it but it didn't work so he changed the 'brew' size. He changed the brew size again and it worked. He eventually went to the original size and it worked - and worked and worked.

I could go through the discussion that followed but I won't. Mines brand new and I've only used it three times to make three different cups. The forth time tried making a pot of coffee and it didn't work at all. So decided to check out the Internet to see if other people had similar problems.

I get answers to use a paper clip or try vinegar. I didn't try either! The place where the K cup goes people were saying to take it out and use a paper clip. Most appliances are made with many parts, so the part where the K cups go comes in three different parts. Take out the part that hold the K cups and that's actually two parts one and two. Underneath parts one and two there's another part which is part three.

Separate the three parts and run them all under water. Doesn't matter if it's hot or cold water. Dry each part and place them together and back into the Keurig coffee maker.

Them your good to go! I hope this information was useful!

Note- After I ran each part under water a hard piece of coffee fell into my sink. I saw roxmel2000's comment about how difficult it is to clean silt-like material off the fine filter at the bottom of the reservoir.

I came up with a solution; take an old toothbrush and heat the handle just above the bristles. When it is hot enough to be flexible,use a heat gun or matches so you can bend the end of the brush to 90 degrees, then let it cool. With the bristles now at 90 degrees to the handle, you can reach down to the bottom with the bristles and gently scrub the fine screen. Flush with a stream of water to get the fine silt out of the reservoir. Works well for us. I had this problem and called the Keurig support number.

They helped me fix it. Your tool bag for this project is a paper clip.

First, take out the plastic holder that holds the K-cups. You should be able to turn it a little and it just lifts out. Once out, take that piece apart.

It easily snaps together and apart. Once it's in two pieces, you'll see the bottom of the small metal tube that pokes the hole into the bottom of the K-cup. Take the paper clip and insert it into the tube and see if you can dislodge any tiny bits of coffee, tea, or whatever you've been drinking. You can run water over the tube while you do this. Second, lift up the handle in front all the way up.

If you look under the lid, you'll see the second set of tubes that inject the water into the K-cup. There should be three tubes. Use the paper clip and clean them out as well.

Put it all back together and get a glass measuring cup. Run three batches of water through the machine without using a K-cup. Each time, note the amount of debris in the water and how much water is being put into the cup. You want the water to be almost clear and the amount to be consistent. If this doesn't work, keep calling Keurig support. You have a 1-year warranty and if it won't work, they will eventually agree and send you a new machine.

(Assuming you have your dated receipt.) My brother got them to send him a new machine because his stopped brewing too. They didn't want it back so he decided to take it apart to see what the problem was.

He said he had a split water line, so in that case, no amount of pipe cleaning was going to help. I use my Keurig every day and really like it.

Fixed my issue with my Keurig, I thought mine was a goner. Even had to get my coffee pot out to resort to it. I was super bummed thanks soo much for posting this! You saved the day! ALSO I'd like to add that in your instructions when you said to look for the three tubes under the handle, my husband and I were having a hard time finding them, to us they looked more like tiny holes that you have to poke through to dislodge any debris of some sort.

Any ways worked for us, and am very thankful, thank you!. We are so disappointed with our Keurig Elite. I've tried the paper clip trick, the vinegar trick, nothing works.

Two issues: 1) It will usually brew a cup of plain water rapidly but as soon as you put in a K cup, the output is reduced to a trickle and after about a minute you have half a cup. 2) Sometimes the reservoir does not prefill for larger cup sizes so all it brews is what's already in the boiler. Personally I believe this to be a combination of two problems: the microprocessor is malfunctioning, and the output pump has some kind of blockage that's significantly reducing pressure. If it weren't for the lack of availability of coffee pods, I would switch to a Tassimo. My friend has one and said he'd never go back to Keurig. We followed the directions but did not clean off the small gold tinted filter that is at the bottom of the reservoir. When we did not get a good flow I then removed the reservoir and gently brushed the fine gold tinted filter at the bottom because I saw a fine coating of what looked like silt from our house water supply.

I flushed the filter with a stream of water after hand rubbing the fine mesh screen and reassembled. That seemed to fix our no-flow problem.

It works fine now. So clearing the sharp needles, plus cleaning the fine mesh filter seemed to be the fix for us. Thanks for all the hints on this site. Very clever solution. Lots of good ideas. Easy to follow instructions. Worth the effort.

Unfortunately didn't work.Seems my K45 is just wearing out. Is barely a year and half old. Even without a K-cup the 12oz button just puts out about 3oz. I use an expensive 'Zero-water' water filter pitcher. Change the filter. So is not hard water clogging.

Guess they just wear out though for a whole year and change only made 2 12oz mugs per week. Now make 6 6oz mugs per week for last two months working at home.

This fix worked for one week and then mine stopped drawing water. (Unplug) I opened the lid all the way. Looked up in the top side with a flashlight and found 2 screws that hold the top cover on.

I removed the cover and could see the rubber tube that brings water into the top. I detached the rubber tube from where it attached and blew (with a straw) until water was dripping out the backflow tube into the water resevoir. I reattached the tube, put the cover back on. Ran through 6 cups so far of exactly 8 oz each time. Thanks this fixed it!

Got a full mug 10oz coffee with a single brew cycle for first time in several months. The stupid P.O.S. 'Zero-water' water purifier pitcher that Bed, Bath&Beyond sold added tiny specks of black gunk that clogged the mesh filter. Saw it when poured 'filtered' water in a clear container had several black specks in it. Not likely healthy either. So lessons learned am just going to use distilled water. Will only be 2-1/2 gallons a month so not that much waste.

Probably wasted more water than that trying to fix this problem. I tried all of the mentioned steps and still had not luck. Then I turned it upside down and hit the bottom with the palm of my hand a few times. Tried once more and it worked. There really isn’t any way to know exactly which part worked - it might have required all of it, or maybe I could have just hit the bottom? Anyway, it didn’t take long and it hadn’t worked for 3 days.

Now I have the carafe filter out though. I couldn’t tell that the screen was coated. I’m wondering if zi should put it back in. I am currently serving in Afghanistan and our Keuring B130 quit working a few days ago.

We had to go back to the old fashioned coffeemaker, which was very painful. I was waiting on my wife to send some Keurig Cleaner from the states, when I got desperate and decided to research it on the web. I found your site, used the paper clip trick, and ran two cups of straight vinegar through it and it works like a champ again. The Taliban can sleep easier knowing that we're no longer Keurig-deprived of our caffeine fix.

Thanks for the very informative site! Happy Holidays to all from Afghanistan! I have B40 unit and i had a problem with this machine when it was not making enough coffee or won't make any at all. Even though the strainer filter at the bottom inside the reservoir looked clean it was full of lint and calcium when i looked though it in bright light - the stainles mesh used to make that filter is super fine and easily clogged.

There are three screws that hold the strainer down. Remove it and put it in vinegar and let it soak. After soaking few hours i took a waterpik water flosser and on high setting pressure-washed it from the outside-in to get rid of all the calcium lint and dust that could have gotten into the water tank. Put the strainer back and screw it together.

Make sure when you screw in the screws you have a good feeling of the thread and find the same grove. Since this cleaning it worked like new and exactly the same amount each time for each cup size setting. Hope that works for you my fellow coffee addicts. Mine was making that labored sound, like the pump wasn't taking a draw. That's because it wasn't!

After I read this, I poured out my reservoir and noticed as i went for the 3 screws that held the filter, that even after the vinegar descaling there was a 'slick' feel to the tank and the filter. As s22nik stated, the filter is so fine that the build up of that invisible gunk was keeping the pump from drawing a full cup thru.

I removed the filter and cleaned it and the tank with Dawn until the tank was squeaky clean. Replaced the filter and the first thing I noticed was when I put the tank in place, bubbles actually came up from the bottom, letting me know that water was actually flowing into the pump. This was the perfect fix! I suggest trying this before you tear your Keurig apart! If none of the above works, remove several screws around the k cup holder and underside of top, also remove one C Clip on the pivot point of k cup holder and slide shaft out the other direction, this removes the k cup cradle and the top trim pieces from the machine.

There is a one way check valve/filter mounted in the top of the unit, mine was stopped up and wouldnt flow in either direction (only supposed to flow outward). I removed it and blew and sucked on it in both directions and it freed up going the one outward direction.

I then reattached it to the hoses but left it loose so I could hang it over the water reservoir. Then I filled reservoir with white vinegar and ran the unit 15 or 20 times and let teh vinegar circulate back into the reservoir. The pump quitened down and it flowed to vinegar very well toward the end. Then i cleaned to vinegar from the reservoir and filled with water and ran 6 or so cups of water through it to get the vinegar taste out. Take the top cover off the brew area removing the two silver screws under the lid where the k-cup is located Removed the zip tie leading to the water filter.

Lifted the black ring that holds the hose that goes to the needle and pull the hose up Blew back down that line and lots of sediment will come out from behind the filter Turn the unit on and let it brew hot water into the holding tank just so you can see if it is cleared. Replaced everything to its original position including putting a new zip tie on the line you removed. This is the third Keurig I have fixed that has had the same problem.

Generally, you have to de-scale the Keurig every three months You don't have to use a whole tank of vinegar. Put a 50/50 mix of vinegar and filtered water in the tank, run it once Let the brewer sit for 45 mins so the vinegar can act on the scale Run it a second time and let it sit for 15. Then empty the tank, washing it throughly or you will get slime that builds up on the side and at the inlet at the bottom of the tank. Now run the clean water through the Keurig for a few passes until you no longer smell vinegar. Was just about to drop 150 bucks for new one but decided to take apart and clean out the part with needle that punctures top of k cup.

I had water backing into the resevoir and when I cleaned out it works perfectly. I actually brewed hot water thru while holding the waterline in my hand into a mug before I put back together. Sounds weird but I held that piece with metal puncture point on it over sink and blew into it and the grinds just shot out into sink. Soaked that part in hot soapy water put back together and works like it's brand new!

Thank you so much!!! I took off the two screws, like you said, and followed your directions, now my 10 year old Keurig is back to her old self, making a full cup of coffee great as ever!!

I did lose a screw somewhere in the machine, but it seems ok with only 1. I know now not to wait till the descale light comes on to descale I will be doing this monthly now. I had descaled 4 times in a row before finding this site. I did the paper clip thing and nothing helped until I blew it out. Thanks again!

The screws on my Keurig aren't the kind you can take off, but I used the paper clip, cleaned the screen on bottom of reservoir and then turned it upside down over the sink (nothing came out, but just in case), plugged it back in to descale with vinegar and voila! Water came out full force!!!

I am a happy camper, thank you thank you thank you! It was taking 4 cycles to get a cup of coffee, and I really didn't want to put out $100+ for a new one. I love my Keurig when it works. Added bonus: I put baking soda in my sink/tub drains and poured the hot vinegar down to clean them, killed two birds with one stone! I have a B70 system. Just tried all the fix-it tricks on here and nothing will help it work again. I can't get one of the 2 screws under the top lid off.

Have unplugged it numerous times and then turned it back on. Even left it unplugged for an hour at a time.still nothing. I can still set all the programming and it blinks and says 'Ready to brew' but about 2 teaspoon of water streams out and then it stops and gets stuck on 'Brewing' mode. Don't want to buy one of the new models out there now. Have had this one since late 2008 so maybe it's outlasted it's usefulness.

Thank u so much! Woke up to no coffee is morning, so sad. I had taken out a few of the wrong screws to take the top off and ended up taking off e handle first instead.

The screws are nestled up inside on either side of the needle that pokes a hole in the top of the k cup. Thankfully I have small fingers to screw them back in. When you take out the right screws the top will lift right off. The hose was full of coffee grounds. Now we know for next time. Thank goodness for your comments and the internet, works amazing!

After cleaning the needle, the pump just would run & sometimes get water & sometimes just hmm & nothing. Tried everything & was ready to toss it. It was only 4 months old. Then I read what to do.

I TOOK OUT THE 3 SCREWS FROM THE BOTTOM OF THE WATER TANK AND CLEANED BOTH SCREENS WITH DISH SOAP & A BRUSH - THIS TOOK OFF AN INVISIBLE FILM AND NOW WORKS LIKE BRAND NEW!! Fyi my wife took it apart before and said I was wasting my time because they were clear - but you can not see the film blockage. I was in the same boat. Half cup brewing. I used paper clips (very helpful) I read to put the whole machine in the sink and use your pressure hose over the water reservoir for 30 seconds to flush the system which im sure helped clean the lines but caused the water to not siphon. I was one step away from either tearing it apart or throwing it in the garbage when I tipped the whole machine upside down and shook it. IT WORKS PERFECTLY NOW!

No clue but hey, it works. Figured I'd share for all those who are at wits end like I was. Ok.Mine had similar issues. After trying all of these I was still unable to get water to flow. So, I took the head apart. I then removed the hose from the nozzle that is in the head. I started to brewer, carefully holding the hose in a cup.

I got some water flow, but not much. I then took the nozzle out of the head and blew through it. Apparently it is a pressure sensitive nozzle and it may have been stuck as I was able to clear it out.

I ran the cycle through the brewer several more time before I was able to get good flow through the hose. I then hooked it back up to the nozzle and it works. I just made a fresh pot.good to have you back Keurig. Be careful with the hose when brewing as the water is very hot. The burping method may have had the most impact as I would have the machine on and tilt it upside down (water reservoir removed) and I could get some flow.

Allok WMV to AVI MPEG DVD WMV Converter Free to try Convert and batch-convert WMV files to other video formats, like AVI, MPEG, MP4, H264, FLV, iPos.

We have never had a problem with our original Keurig. Two things we have done that may have prevented problems. 1) Once a year or so we would run a solution of white vinegar and water through the system (50/50) and 2) was that I always pressed the kcup down in the holder, thereby releasing the pressure and not allowing grounds to go up the water tube. I did that because there were certain kcups were I could stretch the amount of coffee (green mount dark magic) and get one cup of about 16 oz. After brewing my first cup, I would remove the kcup and I would massage the kcup to realign the coffee. I would always place the kcup in the holder at 12 o'clock so that it would be easy to put back in to add to the cup I just made.

I'm still fighting with getting it to suck the water through the system. The WaterPik idea seemed to take care of the mesh opening at the bottom of the reservoir - used WaterPik first on mesh side, then flipped empty reservoir over at a sink and blasted Pik through the outside bottom opening of the reservoir, then I blew air from my mouth through bottom and heard it coming through into reservoir. BUT there still is someplace between reservoir and the 3 needle-holes under lift-up lid that is blocking the flow. Can occasionally blast a small amount of vinegar water with sediment in it out into a cup, but then I try over and over, with periods of waiting in between, to get it to suck more water out of the reservoir, as only less than a half cup comes out the end when it does intermittently work.

I've always been able to de-calcify the machine before using vinegar and a paper clip for the various operations, but this time I'm getting frustrated. It's been mentioned on this list before but I think the procedure for installing the K-cup is very important. For various reasons K-cups often have pressure built up inside. When the top of the K-cup is pierced, when lowering the lid, the pressure blows unbrewed coffee into the upper needles which can cause a clog.

I think it's better to first use your two thumbs to press the K-cup firmly down into the cavity which pierces the bottom and relieves the pressure. That way coffee grounds won't blow up into the upper needles when the head is lowered. As always, good luck and your mileage may vary.

Most of the problems are caused by minerals in the water. Take the tank off and see if there is a strainer (if there is back blow with compressed air, you may have to remove it.3 screws.I did) reinstall and check that water flows freely when valve depressed. Go to store and purchase DISTILLED WATER in gallon jugs (not spring water).about a dollar a gallon.use this only.My problems were.add water light on when full.brewing a half of a cup.descale light on.you may want to descale it at the same time.Mine has been working great for about six months. I placed the kcup pod in the holder,and closed the lid so the pod would get punctured both top and bottom. Without going to the next step, I lifted the lid up and removed the pod to see if it was getting punctured. Well, it was not.

The top was fine but not the bottom, which was barely punctured. So I got a pointy knife (pointy nail works too) and made the hole a tiny bit bigger. The water can now go thru the pod easier. This happens on those pods that look like they are overpacked. The air pressure inside the pods forces the coffee grinds into the water line and clogs up the pins.

I hope I'm naming the parts right and that this fixit is understandable. I have the Breville version, three+ years old. It's a replacement Sur La Table gave me, no questioned asked, when the first one short-cupped after only a month. (I'd owned a Keurig B75 Platinum that had failed twice and been replaced twice by Keurig-and broke again a week past warranty expiration). I use Crystal Geyser water, and sometimes filtered water from the fridge. After it short-cupped sporadically, I descaled 6 mos. Ago, which worked for awhile.

In the past couple of weeks, not only did it start short-cupping drastically but also took forever to heat and brew. Got so that I had to use my espresso machine to add either hot water or brew a shot of espresso into the black coffee in the cup! Did the paper-clip thing on the needles and cleaned the reservoir screens-then it heated a full cup of hot water (slooowly) but only a half-cup of tea. Removed reservoir again to unscrew the top in order to check the hoses (housing the My K-Cup holder and scoop) but found and removed only two screws. And the top would not budge, so I put the screws back in. Next, I removed the reservoir again and hit EVERYTHING that had a hole in it with a blast of canned air.

Keurig Not Brewing A Full Cup Visio For Machine

Then I dragged the machine to the sink, turned it upside down and shook and whomped it on the bottom a couple of times. Brought it back, replaced the reservoir, plugged it in and turned it on. Had to reprogram it-and this time it brewed a full 7-oz. Cup of Sumatra (as swiftly as when new) on the default 7-oz. Keeping fingers crossed. Next time if it malfunctions I will do all of the above plus descale. If that doesn't work, I will let it rest in peace-at its age it's already beaten the Reaper.

Would replace it with a Vue were it not for the huge backlog of K-cups I still have (several months' supply, at an average of six or seven cups a day). But meanwhile, I've developed a taste for a 'red-eye' (that shot of 'spro brewed into a cup of coffee).;-). Here's what I did to solve the problem. You'll need a small screw driver, two small ty-wraps, a paperclip, and vinegar and water.

Here's the process: 1. Descale the brew machine using the instructions from Kuerig 2. Clean out the exit needles using a paper clip per the Kuerig instructions 3. Clean the one-way valve. This valve is located inside the unit beneath the top cover of the unit.

It will gum up and inhibit the flow of water through the unit. Cleaning/blowing it out will fix this issue. Unplug the unit. Remove the water container from the unit. Remove the top cover from the unit. This requires removing the two small screws from the bottom of the top cover.

Open the top as you would to put in a k-cup. The two small screws are located on the top. You'll need a flashlight to see them.

The one-way valve is located on the top and is a larger clear rubber valve attached to the inlet needle on one end and the hose to the heater on the other end. This end is secured with two small ty-warps. Remove the two small screws holding the valve in place. Cut the ty-wraps and remove the valve from the inlet needle and hose. Take the one-way valve and blow it out from the end that was hooked to the heater hose.

I used a small air compressor to clear the valve. You'll see the check valve move open and closed on the inside while blowing it out. Replace the one-way valve. Replace the cover. This can be a pain since it's hard to see the holes and screws.

Be prepared for a few cuss words. If you drop the screws into the k-cup holder you can shake it and they will fall out the bottom. Replace the water container. Plug the brewer in and test.

Now you can run a cup or two through the system. Again I used a small compressor to blow out the one-way valve. This worked best for me and made the repair quick. The unit has been working like brand new since this repair. I had not used my brewer in about 3 months. I turned it on and the water heated up and I pressed Brew, Nothing.

Then the water started coming out of the over flow hose back into the water reservoir. My son took a can of compressed air that he uses to clean the computer. Put the hose of the compressed air into the hole that didn't have water coming out of it. As he did this brown water came out of the brewer where the coffee is normally made and filled a large cup. Then we put more water in the tank and he did it again.

Not as brown this time. The Brewer now works. Brews the correct amount of oz for what is chosen. Thank You Son.

Works great now. OK, this works. You will need perhaps 1.5 hours+. I have the 1-cup version, so I pour one coffee cup of water in for each cup of coffee. This cleaning process is very frustrating at first. If you have a short fuse or limited patience, plan to do this process once per hour over a day, or an evening. Do the following: Drain fill tank, Remove charcoal filter pack, back wash fine mesh screen, run vinegar through system when doing this let the brew tank fill, make one cup then let the vinegar sit a few hours.last run plenty of clear water through brewer to remove the vinegar and any scale that the vinegar loosened, put in a new charcoal filter (you can buy these at the store where you purchased your Kr.

Last get a push pin (like you use to tack notes to a bulletin board). Prior to making a cup, use the push pin to make a small hole near the center of the K cup. This will relieve the pressure in the cup.do this for all K cups prior to using your K brewer will most likely never clog again. Do the cleaning process about ever 6 months, but again. Use the push pin all the time. Paul Battaiola. Thanks to all of you for such great help.

Due to a move, I had my things in storage for about four months. Unpacked it and tried it tonight, it was a no-go. I researched and found this wonderful site! I tried the paper clip to no avail, then I saw both Mark and Cal's posts about the tube being dried out and a burst of air would push the water through. Well, I didn't have anything to push air hard enough to shoot water through the tube except my bike pump. It did the trick! I just positioned the end of the pump (w/o the needle) right over the water hole.

Take the water tank off and you will see it. I pumped hard about three times and water came pouring out of the spot where the coffee comes out. Thanks to all of you!! After having to hit the button 6 times to get a full cup of coffee (for the last 2 weeks!), here are my two cents worth. Get a small phillips screwdriver, a small flat screwdriver, wire snips, needle nose pliers, 10 small zip ties, some type of small wire poker. THIS EFFORT MAY CAUSE DAMAGE TO YOUR PLASTIC PIECES.

Unplug and drain the water. Open the hatch and remove all the screws(4, I recall) holding the lever cover. Remove the cover. Then work very carefully to pry the top back cover from the machine.

I was able to get the left side loose pretty easy. The right and back side clips actually broke off of my unit but didnt damage the fit. These were intended as 'one way clips' with no option of repairability. I was not too worried about this damage and would rather deal with this than drop another hundred bucks on a new maker. Flip the unit upside down and pull out the 5 screws holding the bottom on. Make sure not damage the 3 grounding wires attached to this plate.

Locate the little pump motor and pull the 2 screws holding the motor. Use your needle nose pliers to squeeze and slide off the small hose clamp holding the accordion hose to the side of the pump motor. Flip the unit back over and clip the big zip tie holding the cluster of hoses below the plastic clip. You are trying to locate the bigger tube that runs down to the pump motor. Once located, clip the zip tie on the bigger tube and clip the similar zip tie on the pump motor and remove the length of tube and check valve. Take this whole thing to the sink and flush out the muck(water and vinegar). Use you wire poker to gently push into the check valve to ensure it is cleaned out and working.

Blow into either end of this hose/check valve to make sure you can blow one way but not the other. If you can blow both ways, the valve needs more cleaning and poking. You will also find a similar check valve under the hatch lever. Cut the zip ties at either end of this unit, remove it and do the same cleaning, flushing and actuating of this valve. The crud that came out of my check valves was pretty bad and was the cause of all my problems.

Reassemble everything you took apart. Make sure to get the zip ties back in place on all the tubes and get the hose clamp back on the accordion hose on the side of the pump. It is easier to feed the bigger tube up through the top of the unit before connecting it to the pump. Zip tie the cluster of tubes back under the black plastic clip. Snap the top back of the unit back in place if the tangs didnt break off and if they did, hold it on with clear tape to cover up the booger marks. Tuck the power cord back into the little horseshoe housing and reinstall the bottom cover with 5 screws. This is a more advanced home appliance repair but only took me a little over an hour to accomplish.

My unit is no longer aesthetically perfect but it made a full cup of coffee on the first and only hit of the button. I like the 'industrial-mechanical' look and may just make a clear plastic cover to reinstall on the top of my maker. I had trouble with the Keurig brewing short cups. It would lose its prime. I found that the model I was using had a very tight fitting lid on the water reservoir. When the Keurig tried to pump water from the reservoir a vacuum was created. The water leaving the reservoir needs to be replaced with something.

And that would be air. The pump was just not able to overcome the vacuum. It worked perfectly with the water reservoir cover removed. I wanted to use the cover so I simply drilled a small 1/8 inch hole in the cover near the back of the reservoir.

This is all it took. The air coming through the hole is enough to prevent the vacuum from forming. It's been going strong for over a year. FOR THOSE THAT USED THE PAPERCLIP WITH NO RESULTS: Used the paper clip and it didn't work. I placed a straw over the object that punctures a hole in the coffee pod and blew air through the line- this don't work (btw, the water reservoir needs to be detached if you're going to blow water through the line). I then sucked on the straw once for about 5 seconds and extracted a large amount of water in that short time.

Coffee maker works now!!! Water was not running through at all and this fixed the back up in the line. Just as a precaution, the water is extremely hot when you extract it from the machine via a straw you will get a mouthful of near boiling water. I had an issue with my Keurig B44 whereby the pump would turn on but it would not draw any water up into the heating reservoir. First thing I checked was the mesh filter inside the holding tank which was fine, I then checked the pump which turned out to be pumping water normally.

Keurig Not Brewing A Full Cup Visio For Macbook

Next I removed the top cover and found my issue to be the one way check valve was gummed up. I removed this valve and cleaned it out with some hot water and the issue was resolved.

Hopefully this can help somebody else out who may have the similar issue. I was getting the descale indicator even after descaling, and either no brew or an espresso-size brew when set to 12 oz. A few things I've learned to get it back to work, needing a combination of all these to get back to brewing: - Don't use a paper clip, you risk piercing the plastic hose above the needle. Instead, I use a gum stimulator, like GUM Soft Piks. They're definitely safe, flexible, and the little bristles scrub the needle innards gently. I use the same piks to clear the inside of the needle that pierces the bottom of the pod - mine was completely clogged, but that wasn't the only source of my problem.

You don't need to fill the entire reservoir with vinegar to descale, just one standard bottle of white vinegar plus one same-size bottle of plain water should do. The amount of vinegar in the reservoir doesn't matter, it's the vinegar that sits in the tubing that is working to break down the deposits. Be sure to flush with plain water till you don't have any vinegar smell. I took the top of the lever part off by removing the 2 screws on either side of the pod-piercing needle, then removed the 2 small screws holding down the tubing between the valve and the needle. I then coaxed the tubing off the valve and used a Q-tip to clean the inside of the tubing (it was a lovely shade of brown) and also the firmer outlet from the valve. I then replaced them as they had been.

I replaced the cover of the lever but didn't replace the screws - it stays on very well on its own and will make it easy to remove if I ever need to again (I'm sure I will at some point). FYI, the screws start to strip easily, that's another reason to keep them off, so make sure you have a good grip on them before you start twisting.

I unplugged and did the whole 'flip it over and spank it' stuff, I really don't know if it made a big difference, certainly no more than just unplugging does for just one or two cups, before, in my case, it reverted back to the very short cups. I'm not convinced that unplugging the unit for hours has any great effect that a few minutes wouldn't. I used a can of compressed dusting air, with the thin straw it comes with attached, to spray out the entry point into the machine, where it empties from the water tank. Try to seal off that hole as much as possible around the hole, and put a paper towel over it in case it sprays out. There is a rubber washer around the needle that pierces the top. You can slide it off and wash it - it has ridges that get clogged up with coffee.

This probably doesn't stop the water flow at all, but it is kind of gross. Rather than sucking boiling water out through a straw held firmly around the needle, I attached a straw to a squeeze bottle, taped it on to keep it close to airtight, then gave the bottle a squeeze before holding it over the needle, then reversed the suction of the squeezed bottle by squeezing it at its indents. Did this a few times and it created enough suction to drag out more yuck. This made a big difference.

The rubber washer noted above can be reversed so that a flat side is making a tighter seal with the straw, just reverse it again when you're done. Working well again. Hope this all helps!

I had same problem with all of a sudden not brewing and strained motor sounds. I did the paperclip, then the screen and finally tried to brew and it was making bubling sounds so I blocked air from the little plastic drop thing in back of water redivoir that the water container is usually cut out in top for and I put my finger over it and air bubbles we're backing up from bottom.

So then water started coming out of the coffee point when I released. The liquid was discolored. I did this a second time and got a full cup of water to come out.

I think it was blocked in the tube and that was a way to dislodge it.

ISSUE: Short cup, slow dripping, or no coffee POSSIBLE SOLUTION: The exit needle is blocked with coffee grounds. This can occur if a person removes the lid from a and then tries to brew, or if the K-Cup was not properly sealed at the factory. The grounds can get clogged in the tiny exit needle and cause the brewer to give a short cup or no coffee. To remedy this, the user can remove the K-Cup 'holder' from the brewer and thoroughly rinse with warm water from both the top and bottom sides. This should normally cure the problem.

If the needle is still blocked, compressed air may be used. ISSUE: Brewer will not start the brewing process, there is low pressure, or not filling cups to the top POSSIBLE SOLUTION: Some of the brewers sold from the end of 2009 into the late spring of 2010 had pump issues. Please contact Keurig at 1.866.901.BREW (2739) or check your warranty, because Keurig will replace these defective models. ISSUE: Descale Light is on POSSIBLE SOLUTION: This indicates that the coffee brewer has a build up of mineral deposits that may affect the proper brewing cycle. The brewer may continue to function normally for a while, but should be descaled. To fix this problem:1. Empty the water reservoir.

Fill the reservoir with white vinegar. Place a ceramic cup (not paper) on the drip tray. DO NOT put a K-Cup in the brewer.

Press brew button (you may need to open and close the lid). Empty the contents of the cup into a sink. Repeat until the reservoir is empty. Rinse reservoir and fill with clean water. Let brewer stand for 4 hours while turned on (vinegar is now in tank).

Again place empty ceramic cup on drip tray. DO NOT put a K-Cup in the brewer. Press the 'BREW' button and empty contents in a sink. Repeat until Reservoir is empty (this will drain out the vinegar). Descale light should now be off.